Fantasy Mass Battle WargameEst. 2010

Kings of War Miniature Scale for 3D Printing

Kings of War is a mass-battle fantasy game at 28mm, where entire regiments of identical models share one footprint. Volume is the theme — you are scaling and printing many of the same figure, so the process has to be repeatable and consistent.

Skip to content

What scale am I actually printing?

Miniature Scale
28mm
Ratio Equivalent
1:56
Measurement
eye level
Eye Level Height
28.0mm

Kings of War uses standard 28mm fantasy scale. Mantic's own miniatures are slightly smaller than Games Workshop's heroic 28mm, but the difference is minimal on the table. The game's regiment-based movement system means individual miniature scale matters less than unit footprint.

Publisher: Mantic Games·Base Sizes: 20mm, 25mm, 50mm, 100mm, 120mm

I set up one saved slicer profile per regiment and reuse it for every copy, which is what makes mass printing fast. Because all the models in a unit need to match, I scale the first STL to exactly 28mm, lock XYZ, and apply that same profile to the whole batch rather than re-adjusting per file.

Regiment trays mean I rarely worry about per-model base variety, but I do check that every printed copy lands on the tray without overhang. Batch consistency beats chasing one perfect miniature here.

Deep Dive: Regiments at 28mm, printed fast

Kings of War is 28mm and accepts any range, but you need whole regiments. This is the one game where volume beats detail — the printing strategy is batches, not individual heroes.

The 28mm Mantic Baseline

Kings of War uses standard 28mm fantasy scale. Mantic's own miniatures run slightly smaller than Games Workshop's heroic 28mm, but the difference is minimal on the table. Because the game uses regiment-based movement, the unit footprint matters more than the exact height of any single model — a fact that takes a lot of pressure off your slicing.

Batch Printing for Regiments

You need entire regiments, not single characters. I print infantry in large batches at 0.4mm nozzle and 0.1mm layers for speed, and treat the movement trays as printable pieces — Mantic's trays clone cleanly. Rank-and-file troops are viewed from several feet away, so the quality bar is lower than any skirmish game.

Converting 32mm STLs Down

Conversion Formula Slicer %
AoS/40k (32mm) → KoW (28mm)28 ÷ 3287.5%
KoW (28mm) → AoS/40k (32mm)32 ÷ 28114.3%

Most fantasy STLs are 32mm heroic. Bring those down at 87.5% to keep a KoW regiment consistent with Mantic's slightly-slimmer 28mm look.

Characters and Champions

Unit champions and characters are where the detail budget belongs. I print those at 0.2mm nozzle and 0.06mm layers so they read as individuals in the block. Everything else is production work.

Common Kings of War Mistakes

  • Obsessing over individual scale inside a ranked block. Footprint and base size carry the unit. Height differences of a model or two vanish at table distance.
  • Solid infill on rank-and-file. Grid infill saves filament and the models are strong enough for handling — you are printing dozens of them.
  • Fine layers on everyone. Running a whole regiment at 0.06mm is a waste of hours when the unit reads the same at 0.1mm.

Scale Conversions for KoW

Slicer percentages for converting between Kings of War and other common miniature scales.

Scale conversions for KoW
ConversionDescriptionSlicer %
28mm → 32mmKoW to AoS Scale114.3%
32mm → 28mmAoS to KoW Scale87.5%
28mm → 35mmClassic to Legion/MCP125.0%
28mm → 1:35Tabletop to Model Kit163.2%

Printing these minis on FDM

Batch infantry prints at a 0.4mm nozzle and 0.08mm layers for speed and consistency. Save a single 28mm profile and reuse it across the whole regiment so every copy matches.

All settings tested on my Bambu Lab A1 Mini with PLA. Your printer may want something different — always print a test piece first.

Frequently Asked Questions

What scale is Kings of War?
Kings of War is a 28mm mass-battle fantasy game where entire regiments share a footprint.
How do I keep a regiment consistent when printing?
Save one 28mm slicer profile, apply it to every copy of the STL, and print the whole batch with identical settings.

Kings of War and all related names, ranges, and units are trademarks of Mantic Games. STLACCESS is an independent hobby project — not affiliated with, endorsed by, or sponsored by any game manufacturer or publisher. Names appear only to identify miniature scales and printing settings; no branded files, models, or artwork are hosted here.Full trademark notice

Time to check the scale before you commit to a long print.

Launch the STL scale calculator