Sci-fi WargameEst. 1987

Warhammer 40k Miniature Scale for 3D Printing

Warhammer 40k is where most people first trip over the gap between sculpt generations. Primaris Space Marines sit at 32mm heroic scale, while older Firstborn sculpts and countless third-party proxy files are sized for 28mm. Getting a printed proxy to stand correctly next to your painted army means deciding which baseline your file was actually built on — then setting one clean slicer percentage instead of eyeballing it.

Skip to content

What scale am I actually printing?

Miniature Scale
32mm
Ratio Equivalent
1:50
Measurement
eye level
Eye Level Height
32.0mm

Games Workshop uses heroic proportions — heads, hands, and weapons are intentionally oversized so details read at arm's length. A Primaris Space Marine stands roughly 32mm to eye level, while a Firstborn Marine measures about 28mm. Mixing the two on the same table is noticeable but acceptable for casual play.

Publisher: Games Workshop·Base Sizes: 25mm, 32mm, 40mm, 50mm, 60mm, 80mm, 100mm, 120mm

When I scale Warhammer 40k STLs, I start by measuring eye level in the slicer rather than trusting the file's title. A file labelled 'heroic 32mm' that actually measures 35mm to the eyes will print oversized against a genuine Primaris, and no percentage math can fix a file built on a different reference point. I check the sculpt first, then apply the conversion.

The single most common job is bringing 28mm Firstborn or proxy infantry up to 32mm. That is a 114.3% uniform scale on my Bambu Lab A1 Mini. For vehicles I prefer to scale against a known reference model rather than a formula — Rhino and Land Raider chassis were designed around specific Primaris proportions and sculptor variation is too wide for a universal number.

Deep Dive: Primaris vs Firstborn

Warhammer 40k has one of the most confusing scale landscapes in tabletop gaming. Between Primaris, Firstborn, older sculpts, and third-party proxies, knowing what percentage to type into your slicer is not always obvious.

The Two Scales of Warhammer 40k

Games Workshop uses two distinct scales depending on the model range:

  • Primaris / newer sculpts (2017+): 32mm heroic scale, measured to the eyes (160cm on a 175cm baseline)
  • Firstborn / older sculpts (pre-2017): 28mm true scale, also measured to the eyes

A Primaris Marine is roughly 14% taller than a Firstborn Marine. This is not scale creep — it is intentional. The Primaris range was designed with truer human proportions, which means longer legs and a taller frame.

Conversion Cheat Sheet

Conversion Formula Slicer %
Firstborn (28mm) → Primaris (32mm)32 ÷ 28114.3%
Primaris (32mm) → Firstborn (28mm)28 ÷ 3287.5%
28mm → 40mm (terminator / gravis)40 ÷ 28142.9%
32mm → 40mm40 ÷ 32125.0%
28mm → 75mm (display scale)75 ÷ 28267.9%

How to Scale a Primaris Proxy on FDM

Most Warhammer 40k STL files you find online are designed for 32mm heroic scale. Here is how to handle them on an FDM printer:

  1. Check the sculptor's baseline. If the description says "32mm scale" or "heroic 32mm," you can print it as-is for a Primaris army.
  2. Measure eye level in your slicer. Import the STL, use the measurement tool, and check the distance from the bottom of the foot to the eyes. If it is not 32mm (or close), scale it.
  3. Set your layer height to 0.08mm. This is the sweet spot for 32mm heroic miniatures on FDM. Detail is good enough for tabletop distance, and print time stays reasonable.
  4. Use a 0.2mm nozzle for faces. If you have one, swap to a 0.2mm nozzle for character models. The difference in facial detail is significant.

What About Vehicles?

Warhammer 40k vehicles use a different scaling convention. A Rhino chassis is designed to look correct next to 32mm Primaris models. If you are printing a vehicle STL labelled "for 28mm," scale it up to 114.3% to match your Primaris force.

For larger vehicles like Baneblades or Titans, scale by comparison to a known reference model rather than using a formula. Vehicle proportions vary too much between sculptors for a universal percentage.

Scale Conversions for 40k

Slicer percentages for converting between Warhammer 40,000 and other common miniature scales.

Scale conversions for 40k
ConversionDescriptionSlicer %
28mm → 32mmFirstborn to Primaris114.3%
32mm → 28mmPrimaris to Firstborn87.5%
32mm → 40mmStandard to Terminator125.0%
32mm → 75mmTabletop to Display234.4%

Printing these minis on FDM

For rank-and-file infantry I use a 0.4mm nozzle at 0.08mm layers. Character models and anything with exposed faces earn a 0.2mm nozzle at 0.06mm layers. Vehicles and terrain tolerate 0.12mm layers without visible loss. Scale your STL to the percentage above, lock XYZ, and always print a single test piece before a full squad.

All settings tested on my Bambu Lab A1 Mini with PLA. Your printer may want something different — always print a test piece first.

Frequently Asked Questions

Is Warhammer 40k 28mm or 32mm scale?
Modern Warhammer 40k (Primaris range, 2017 onward) is 32mm heroic scale measured to the eyes. Older Firstborn and classic sculpts are closer to 28mm true scale. Scale up 28mm STLs to 114.3% to match a Primaris army.
How do I scale a 40k proxy STL?
Measure the file's eye level in your slicer first. If it is a 28mm Firstborn proxy aiming to stand next to Primaris, apply a uniform 114.3% scale. If the file is already 32mm, print it as-is.
What is the best FDM profile for 40k infantry?
A 0.4mm nozzle at 0.08mm layers handles rank-and-file well. Swap to a 0.2mm nozzle at 0.06mm layers for character models so faces and weapons stay crisp.

Warhammer 40,000 and all related names, ranges, and units are trademarks of Games Workshop. STLACCESS is an independent hobby project — not affiliated with, endorsed by, or sponsored by any game manufacturer or publisher. Names appear only to identify miniature scales and printing settings; no branded files, models, or artwork are hosted here.Full trademark notice

Time to check the scale before you commit to a long print.

Launch the STL scale calculator